PRICING
- 3’6″ x 65’6″ (230 sq. ft.) SSDM / 1.07m x 20m $138.00
- 5’0″ x 65’6″ (325 sq. ft.) SSDM / 1.50m x 20m $195.00
- 6’0″ x 65’6″ (393 sq. ft.) SSDM / 1.83m x 20m $235.80
- 6’7″ x 65’6″ (431 sq. ft.) SSDM / 2.00m x 20m $271.53
- 7’4″ x 65’6″ (480 sq. ft.) SSDM / 2.24m x 20m $312.00
- 7’11” x 65’6″ (518 sq. ft.) SSDM / 2.40m x 20m $336.70
- 8’11” x 65’6″ (583 sq. ft.) SSDM / 2.70m x 20m $458.10
- 9’11” x 65’6″ (648 sq. ft.) SSDM / 3.00m x 20m $503.60
- 11’6″ x 65’6″ (754 sq. ft.) SSDM / 3.50m x 20m $580.02
- 13’2″ x 65’6″ (861 sq. ft.) SSDM / 4.00m x 20m $788.80
- DimpleGrip Molding (Bundle of 40 ft)$45.11
- Membrane Cap Molding (Bundle of 40 ft)$21.95
- SuperPlug (Bag of 50)$15.59
- Small Plug (Bag of 100)$11.02
SHIPPING
Standard Shipping: 3 – 7 Business Days
All shipping times are estimated and may not be 100% accurate. Shipping times may vary based on location and order size. Most orders are shipped within the next business day.
Healthier Homes start with SUPERSEAL.
Helps to control moisture from entering into soft surfaces, such as couches, carpet, laminated wood, etc. By installing SUPERSEAL the membrane can help to control moisture from within concrete floors and walls from getting into the living space. It can be used as a subfloor under new floor finishes, and it can be used as a wall barrier for leaking or damp walls. Along with a ventilating system SUPERSEAL can provide a much dryer basement.
How to save money by using SUPERSEAL membrane to make your basement dry
You have a basement with exterior walls that are damp or leaking. Your choices are:
Option #1 install: SUPERSEAL membrane on the inside of the foundation connected to a French drain, eliminating the water from getting into the basement. This may be the most cost effective way with the least amount of labour.
Option #2: Remove you landscaping and sidewalks, and dig out the exterior of your foundation. Install a new drain system and SUPERSEAL membrane, and then replace the landscaping and sidewalks.
Dimpled Foundation Membrane Interior French Drain Application
Pick a roll size that goes from the exterior grade height down the wall to the French drain system. Example: Let’s say the wall is 7 feet to grade height and you need another foot to make it into the French drain. The roll size would be 7 feet 11 inches. Allow for bends and curves to ensure you have enough membrane.
Install the membrane to the grade height marked on the wall and fasten every 5 feet with a SuperPlug 4 inches from the top. Then fasten the membrane in the middle and at the bottom. Use a tar base or caulk to seal around the nail head.
Ensure the end of the membrane goes into the French drain stone and that the drain goes to a sump pump or to day light by gravity.
Finish the membrane by installing an end cap and top cap. If you can fasten the membrane to the framing plate you will not need a top cap. The purpose of installing the membrane from the grade height to the French drain and capping the edges is to ensure that the entire wet surface is enclosed within the membrane. This helps eliminate the surface moisture from getting into the moving air within the basement, which will then absorb into soft surfaces, such as couches and carpets.
SuperPlugs– Fastens the membrane to the wall
Membrane Cap molding (optional) to cap the sides or the top if required
Specifications
PART # | IMPERIAL | METRIC | ||||
SM36107 | 3’6″ X 65’6″ | 230ft² | 29 lbs | 1.07m x 20m | 21.4m² | 13kg |
SM50150 | 5’0″ X 65’6″ | 325ft² | 40 lbs | 1.5m x 20m | 30m² | 18kg |
SM60183 | 6’0″ X 65’6″ | 393ft² | 49 lbs | 1.83m x 20m | 36.6m² | 22kg |
SM67200 | 6’7″ X 65’6″ | 431ft² | 53 lbs | 2.0m x 20m | 40m² | 24kg |
SM74224 | 7’4″ X 65’6″ | 480ft² | 59 lbs | 2.24m x 20m | 44.8m² | 27kg |
SM80240 | 7’11” X 65’6″ | 518ft² | 64 lbs | 2.4m x 20m | 48m² | 29kg |
SM81127 | 8’11” X 65’6″ | 583ft² | 72 lbs | 2.7m x 20m | 54m² | 33kg |
SM91130 | 9’11” X 65’6″ | 648ft² | 80 lbs | 3.0m x 20m | 60m² | 36kg |
SM11635 | 11’6″ X 65’6″ | 754ft² | 93 lbs | 3.5m x 20m | 70m² | 43kg |
SM13204 | 13’2″ X 65’6″ | 861ft² | 107 lbs | 4.0m x 20m | 80m² | 47kg |
Tested and Passes The Following |
|
Dimpled Sheet
|
High Density Polyethylene (HDPE)
|
Available Colors
|
Black (Standard), Brown (Special order)
|
Compressive Strength
|
5200 psf (250 kN/m² )
|
Dimple Height
|
5/16″ (8mm)
|
Fire Rating
|
B2 (DIN 4102)
|
How do I use SUPERSEAL membrane to control the water and moisture that is leaking through my foundation wall?
You can use SUPERSEAL to manage the water that comes into your home from a cracked foundation. You install it and connect the bottom of it into a French drain system.
I have a rising water table in my basement, how do I control the water using SUPERSEAL?
Install the membrane with the dimples down and pour a new concrete floor over the membrane. The space created between the dimples and old floor will allow the water to be directed to the drain system. Ensure the drainage system is located in areas were the water needs to be removed from.
Question
Ulises Gutierrez –
Select DimpleGrip Molding
(Is there any way can you tell me how many pieces and how long each piece is thank you
Watch Unwatch
SUPERSEAL –
Yes, there is 10 pieces per bundle and they are 4 feet long.
Question
Brian Doyle –
Is there an adhesive that can be used for seaming? Everything I’ve tried peels off when it dries.
Watch Unwatch
Ross Carmen –
you can use any foundation mastic, roof patch, plastic cement. If you use a self adhesive membrane, you need to use it with the primer.
Question
Chris Jankowiak –
What are my options for fasteners. I received my roll of membrane, cap and plugs. This will be going on a basement block wall. Tapcons? some sort of nails? I’m hoping for the quickest most effective method. Tapcons seem like too much work with drilling pilot holes.
Watch Unwatch
Ross Carmen –
1 1/4 x 3/16″Tapcons are the safest bet. Yes it is more labor intensive but most block walls are hollow and you run the risk of damaging them if you use a powerful concrete nailgun.
Chris Jankowiak –
Thanks will do!
Question
Brad Kemper –
Hello..I have a standard block foundation basement in my home built 2006 with drop ceiling in it and am wanting to apply this to back wall but not sure what size roll i need as the excavation hasnt started yet. Is there a way to tell the height of roll i would need for this application? Also is there a standard amount of hardware/plugs/moulding/cap for each size roll you buy? My basement is 55′ long on back wall and id say from floor of basenent to drop ceiling is approx 7ft.
Thanks
Brad
Watch Unwatch
Ross Carmen –
A test hole is best to determine the roll size. Its hard to determine the measurement because the distance varies in most homes from the top of the footing to top of slab. The rolls can easily be cut to height once you determine the exact measurement when you excavate. Ensure the roll is high enough. We offer a 8’11 roll. 2 bundles of dimplegrip molding and 2 bags of superplugs will work for you. You may have a few pieces of molding left over.
Question
Mark –
Question in regards to the DimpleGrip molding. I can’t find anything that says what type of fasteners to use, (what length, tapcons?) and placement of said fasteners on the molding. Thanks
Watch Unwatch
Ross Carmen –
1 1/4″ x 3/16 Tapcons will work the best. Concrete nails 1 1/4 or 1 1/2″
Question
Mike –
When will 7’11” Dimple Board be Available ?
Watch Unwatch
Ross Carmen –
Hi Mike ..I sent you an email…let me know what you would like to order and a ship to address and I can give you a delivered price….thanks
Question
David –
If this product is exposed above grade can it be protected from breaking down by coating it with exterior latex paint?
Watch Unwatch
Ross Carmen –
The membrane will expand and contract with temperature changes and paint will crack when this happens. You can use a elastomeric paint that will flex a bit and last awhile but not long term. The membrane is not supposed to be exposed to UV for long periods of time. It is best to cut the membrane off and cap or seal the top at grade height.
Question
Nag –
I am purchasing this for basement internal walls; Like to know if this material breaks down like you explained for external application on Aug 12 2021 comment as response to Bryan. As per below comments interior application also over time exposed to cold and warm conditions in various seasons; I will not be able to reach / inspect this material after framing , insulating & dry wall on top of this Dimple mat attached to concert wall and tucked into the parameter gap around by basement.
Watch Unwatch
Ross Carmen –
Direct sunlight and UV rays is what will break it down on the exterior. No concerns for your interior application.
Question
Josue Morales –
I am looking for high flow drainage membrane
Watch Unwatch
Ross Carmen –
How many square feet?
Question
Jake –
How do you install this product around steel wall bracing? Or is this supposed to go on before installing steel?
Watch Unwatch
Ross Carmen –
Hi Jake,
can you send a few pictures to info@superseal.ca ….thanks….
Question
bobby04040 –
I’m thinking of installing mat over part brink and part concrete basement walls the putting insulation board directly on the mat. Would this be advisable? Unfinished basement with no studs and french drain around perimeter.
Watch Unwatch
Ross Carmen –
The membrane is mechanically fastened to the wall. Rigid insulation fasteners can be used to fasten the board through the membrane and into the wall
Question
Bob –
do you have any idea when you will start shipping again?
Watch Unwatch
Ross Carmen –
Hi Bob,
We are hoping for the end of June….thanks….we will put inventory back on the shopping cart when we do.
Chris –
For a foundation block wall, what liquid applied product is recommended as a first layer behind your membrane system?
Ross Carmen –
Superseal is compatible with any waterproofing or damproof coating. There is alot of options and manufacturers. More expensive coatings perform better.
Question
Vanessa Williams Madinah –
Is there somewhere locally which can purchase this product in Illinois?
Watch Unwatch
SUPERSEAL –
The best way to purchase is ONLINE at https://www.superseal.ca/ or call 1 800 571 1877. Please allow 2-3 days for delivery. You can also special order through your local Menards store. Thank you
Glen –
Do you have photos of interior basement wall installs?
SUPERSEAL –
https://www.superseal.ca/foundation-membranes/interior-applications/ click to view the interior application on our website
https://www.alljerseyinc.com/jersey-shore-basement-mold-remediation-and-new-concrete-floor/
Thank you
Question
Marian Kasker –
What can my friend put over this (and how) to get a finished basement again? She had flooding from a hurricane & this is what the contractor put up and left her with. She has a sump pump. It looks horrible. She used to have a lovely finished apartment in the basement. Now no one knows how to finish the walls to put up paneling or whatever. She just has this “stuff” flapping loose on her walls.
Watch Unwatch
bhavani hamann –
Can you use dimpled water seal subfloor on outdoor wooden deck? To be used under deck vtiles?
Ross Carmen –
what type, brand, and thickness of tile?
SUPERSEAL –
Please send a few pictures…thank you
Question
Jimmy Williams –
What type of tool do you use to fasten it to the block? Is it pneumatic?
Watch Unwatch
SUPERSEAL –
For hollow block walls it is best to use 11/4″ x 3/16″ tapcon screws through the center hole on our superplug. If the blocks are filled you can use any type of concrete nail gun. It is best to test a spot first as a concrete nail gun could damage the block.
Beth Holder –
Have you been able to resume shipping to the US yet? If so, what would estimated shipping time to Kansas City, Missouri, USA be?
Ross Carmen –
Hi Beth,
Not at this time….we are hoping for the end of July….thanks
Question
Don Wantke –
Are you out of stock on every thing because of the corona virus or out of business? I would like to order some dimple board and accessories for my basement. Do you have any idea these will become available. Thank You
Watch Unwatch
Doug –
Have you resumed shipping to the US? Do you install the dimples toward the foundation wall or toward the back fill? If installed toward the backfill what would keep dirt out of channels? Can you backfill gravel directly toward the dimpleboard flat side?
Ross Carmen –
Hello Doug, yes we have started shipping some roll sizes….see our shopping cart. You will receive a separate email. Please provide a list of required product and a ship to address. We can give you a delivered price…thanks
Ross Carmen –
Thanks you for your interest. Due to the Corona Virus we have temporarily shut down all shipping. We will send you an email when we resume. We are hoping by the end of May. Sorry for any inconvenience.
john charles mikols –
how do you install the select membrane cap? i am putting it on a wood retaining wall. do i nail through the membrane cap using a small plug for each nail?
Ross Carmen –
You can use nails or screws directly through the cap. Small plugs and superplug are fastened with a nail or screw. Plugs are not used with the cap or dimplegrip molding
Gerry Mitchell –
I hope you are all doing ok, any idea on when you will start shipping?
Thanks and stay safe!
Ross Carmen –
Due to the recent spread of Covid 19….Superseal has temporarily stopped shipping in the USA.
We will respond by email when we resume sales.
We apologize for any inconvenience this may cause.
We were hoping to resume in June 2020…..unfortunately…..
We are now hoping for end of August… We will put a notice on our website and inventory in our shopping cart when we start up sales again. We will also send you an email update. Thanks for your interest in Superseal and patience during this time.
Please confirm receipt of this email
I can ship orders with 6 rolls or more….. they can be mixed sizes and accessories….and I need a tax ID #.
Question
Anthony Gregg –
If I used a Ramset Powder Actuated Gun with Ramset 1 1/2″ nails on the Super Plugs would that be okay given that the nails already have a plastic collar on them? So then there would be the collar and the Super Plug attached to the concrete wall? If not, how else would I do this using a Powder Actuated Gun? Thanks.
Watch Unwatch
Tim Williams –
We are building a wood retaining wall with 3″X12″ boards which vary in height between 3′ and 9′ height. Can we buy rolls of 3’6″ and overlap for the taller sections of the wall?
Ross Carmen –
Yes you can. I believe we spoke on the phone. Thank you for the order
Ross Carmen –
Anthony, yes you can…test a spot first as concrete varies in hardness and strength all across North America.
Question
Ernest –
I live in the Us and already have membrane and trim but no plugs to hang. Is there a alternate item to use since you are not currently shipping to US. I’m in middle of project and would like to get foundation finished up. Thx
Watch Unwatch
Ross Carmen –
Hi Ernest….give me a call when you have a chance….1 800 571 1877….thanks
Amber –
I have had trouble from the start with this product. Wish i never had it installed. Water gets trapped between the block and tge membrane and my basement walls are always damp! I hate it
Watch Unwatch
Ross Carmen –
Please give us a call when you have a chance…800 571 1877…..thanks
Question
BRYAN BRADLEY –
CAN TOP BE LEFT EXPOSED TO SUN
Watch Unwatch
Nag –
It is under “Interior Applications – French Drain” –SUPERSEAL Dimpled Membrane; Like to know if we face same issue as external with breaking over time. if installed in basement internal to cover concert wall.
Ross Carmen –
no concerns for your application
Ross Carmen –
The membrane should be covered within a few months of installation. After a year or two….the membrane exposed will start to break down. It should be terminated just below grade.